Grenaded :-(

[Jacked Hemi]

Went and played in the mud last night and got a little carried away I guess. Snapped my cv-shafts to bits.. :peelout: Gotta pay to play I suppose.. Does anyone make some beefy cv-shafts?

[Jacked Hemi]

Yeah, that's what I did. I might just leave it 2WD to keep myself outta trouble.. haha

[Sprocket]

I wish someone would make some stronger componets that arnt a arm and leg. Id like to add some strenght to my truck.

[SharaDon]

KORE Racing makes some upgraded CV knuckles. We have yet to install on Jerry's truck.

I don't know how much they cost?

[Carrolls Ram]

What were ya doin to break it?

[Moby'sHEMI]

That sucks. I did that when I first got my truck. The only good part is you can pull the shaft and run it around still while you wait for another

That blows, but now you can do low range burnouts!

[Jacked Hemi]

I was in a pond 3' deep with a hard bottom and then it dropped into a 4' hole with a gooey bottom so I gunned it and at some point in doing so it popped.
I was thinking of trying to drive it in 2LO on the street, i've got 38's with 3.92's for now. 7.84:1? haha

[DaKing]

man, that sucks..

can you take & post some pictures of the CV joint?

also wore your tires turned when it popped?

my fear is to break the CV_joint...

[hemi1569]

rich where abouts were you? Up in the adirondacks? I would like to take mine bogging but not 4' holes! I was just up at the lake sunday

[Jacked Hemi]

I was at the south end of LG off of Rt. 149 at my friends logging trails / beaver ponds. I know of a few places around here to sling a little mud.

I'll post some pics in a bit. My tires weren't turned, I twisted the shaft out of the inner cup. Not used to wheeling with the 268 and at about 3500 rpms it just reved out and I wasn't expecting it.

I stopped by the campground on Sunday, but I really didn't know what I was looking for.. haha

[Jacked Hemi]

Few shots of the Shaft (haven't cleaned all the grease out yet), some shots of the angle, a bad shot of the rig and also a shot of the new mud project. (Jeep YJ, 2.5 ton rockwells and 48" tractor tires.. :finger2: )

[hemi1569]

We'll have to meet up sometime rich, looks like fun

[johnnyk416]

Seen ya today Rich on 254 around 1:00.......... truck is lookin real good man:Tup:

[Jacked Hemi]

Where is 254..? I went down around the Glens Falls area today. I didn't know anyone lived remotely close to me.

[Jacked Hemi]

After looking at your gallery, I remember spotting your truck today. I took the girl down to shop for a truck, she wants me to build her one just like mine. Found a nice '06 for her, have to see what the bank says!

[johnnyk416]

After looking at your gallery, I remember spotting your truck today. I took the girl down to shop for a truck, she wants me to build her one just like mine. Found a nice '06 for her, have to see what the bank says!

Nah I wasn't in my truck, I was in my work truck. 254 is exit 19 aviation rd turns into quaker it is where all the dealers are. When I first met ya was at the HTC GTG mopars at the valley 2 yrs ago, man your truck has definitly gone through a nice transformation.

[dline]

your angle on your CV shaft seems pretty extreme

[johnnyk416]

your angle on your CV shaft seems pretty extreme

I was gonna say that to, I don't think a stronger shaft will help because it looks like it just pulled out of the cup.

[Jacked Hemi]

I thought it was a harsh angle too, but wanted opinions. As much as I don't want to, I think i'm gonna bring the front down 1"-2". (Anyone wanna buy a mostly stock-ish'04 Ram..?) :finger2:

[Jacked Hemi]

so today I was cruising on I-87 and somehow snapped three wheel studs.. SAS time.. :whocares: Truck is sitting in a U-turn if anyone wants to burn it.